Extruder equipment, extruders and converting and extruders systems

Quick Article Nav

Extruder Equipment Community - Welcome to extrusion.plastics.com

What is Extrusion...[continued]

Single-screw extruders

In a single-screw extruder, the screw has a deep-channeled feed section that transports solids from the feed throat and compresses them, a transition or compression section where the channels become shallower and the polymer is melted, and a shallow-channeled metering section where the melt is conveyed to the extruder equipment diagramadapter and die. Different polymers process best with different compression ratios (the ratio of the feed zone depth to the metering zone depth). Some resins melt better in a screw that has barrier flights in the transition section to separate the melt pool from the remaining solids bed. Some screw designs incorporate mixing devices such as pins or barriers to flow. Static mixers, which interrupt the melt flow, create distributive mixing and are used to make melt temperature more uniform. Extruder equipment; single-screw extruders, are used in simple compounding operations, such as mixing color and additives into a polymer, although Kneaders and twin-screw extruders are more often used for compounding extrusion that requires highly dispersive mixing. Relatively new mixing screws for single-screw extruders improve both distributive and dispersive mixing for more demanding compounding operations. extrusion equipment diagram

Single-screw extruders are widely used for extruding film, sheet, and other applications that use pre-compounded pellets.

The Buss Kneader is a special type of single screw extruder equipment with a screw that both rotates and oscillates axially. The Kneader has a full spiral screw in the feeding and devolatilizing zones. In the mixing and kneading zone, the spiral is interrupted with kneading flights that intermesh with kneading teeth or pins fixed inside the barrel. The Kneader is widely used for compounding PVC pellets, because it operates at low shear and low temperature. It is also used for direct extrusion of PVC calendered film.

Twin-screw extruders

extruder equipment - corotating and counterrotating fullySeveral different types of twin-screw extruders (TSE) are used for different applications. Parallel twin-screw extruders have two screws that rotate in the same direction (corotating) or opposite direction (counterrotating), with non-intermeshing or fully intermeshing flights. Parallel twin screws are modular, and the screw design can be changed by rearranging feeding, venting, mixing, and pumping elements along the screw shaft. Corotating TSE are commonly used for compounding, while counterrotating TSE are often used for direct extrusion.

Types of parallel twin screw extruder equipment.

Conical, counter-rotating twin screws are tapered and made in one piece. Conical TSE are used primarily for processing PVC into pipes and profiles. The lower shear of conical TSE is an advantage for shear-sensitive materials like PVC. CPM conical counterrotating twin screw extruder equipment screw shafts

While single-screw extruders are typically flood fed, with the feed filling the screw channel, twin-screw extruders and extruder equipment are typically starve fed, with only a partially filled screw channel. Because the screw channel is not completely filled, downstream feedports or vents can be easily added. Adding shear- or heat- sensitive ingredients downstream, after the polymer is melted, helps keep them from degrading. Fibers can be added downstream to reduce screw wear and to preserve their aspect ratio. Vents are used to remove volatiles, such as water entrained in the mixture, from the melt. Compared to single-screw extruders, TSE are better at feeding and conveying, especially of powdered material or large amounts of fillers, and typically create more dispersive mixing.






Davis-Standard, LLC | Click to visit the Davis-Standard website

Davis-Standard, LLC provides this marketplace micro-site!

    extrusion process control equipment

  • Davis-Standard :: the Extrusion Industry Leader
    Davis-Standard, LLC (D-S LLC) is a global leader in the design, development and manufacturing of extrusion systems, feedscrews, barrels and process controls
  • aftermarket extrusion equipment
    compounding equipment
    elastomer extruders
    monofilament, multifilament, melt blown, spun bonded, and other fiber processes
    foam extrusion equipment
    laboratory and pilot equipment for cast film, blown film, tubing, sheet, coating, fiber, compounding, elastomer, and fine wire applications.
    pipe, profile and tubing extruders and systems
    process control equipment for extrusion, extruders
    reclaim extruders and systems for post industrial and post consumer processing.
    foam, flexible and rigid sheet extrusion, and single and multi-layer coextrusion applications up to nine layers.
    wire and cable equipment, extrusion equipment

  • Your Extrusion Experts
    Are Right Here...

    fold faq Facilties (click for details)
    fold faq Markets (click for details)
    fold faq History (click for details)
  • Fill out my online form.
  • For More Information
    Call or visit our website:
  • Davis-Standard, LLC
    North America+860-599-1010
    DS Brookes, Ltd.: +44 (0)1384 471930
    ER-WE-PA GmbH: 49-211-2404-0

  • Davis-Standard, LLC provides this marketplace micro-site!
  • Click for details about sponsoring a content targeted lead gen micro-site

Davis-Standard, LLC | Click to visit the Davis-Standard website